Assigning specific VHF (134-174 MHz) or UHF (400-470/450-520 MHz) frequencies to each channel.
pigtail (DIN to 3.5mm jack) that connects the FIF-12 to the radio’s accessory port. Operating System : The software was originally designed for Windows 2000, XP, Vista, and 7 . To run it on Windows 10 or 11, you may need to use Compatibility Mode (set to Windows 7). Quality Two-Way Radios Step-by-Step Programming Setup Configure the COM Port : Open CE86, go to File > Configure , and select the COM port assigned to the FIF-12. Adjust Baud Rate : Set the baud rate to
The primary application used to program the VX-351 is the .
While waiting, he opened the tab of the software. Here lay the real power: TX Save (battery saver), Time-Out Timer (set to 60 seconds to stop chatterboxes from jamming the channel), BCL (Busy Channel Lockout), and Compander —a noise reduction feature that, when enabled, made audio sound like angels whispering through cotton.
He enabled Compander on all floor supervisor radios. It would reduce hiss and background slot machine noise. He disabled it on security radios—they needed raw, uncompressed audio to hear the nuance of a drunken argument.
. Users on Windows 10 or 11 may need to run the software in "Compatibility Mode" or use a Virtual Machine running an older OS. Programming Steps Driver Installation : Install the drivers for the cable before connecting it to your PC. Configuration Open the software and navigate to File > Configure Select the correct (it should show "FIF12" in parentheses). Baud Rate to 38,400 to ensure stable data transfer and prevent timeouts. Reading Data Ensure the radio is when you connect it. Select the "Read" or "Upload" option in the software. Turn the radio only when prompted by the software to begin the transfer. Editing & Writing
Here are some common programming tasks for the Vertex VX-351:
Once the software and cable are communicating, follow this specific sequence to avoid data corruption: Plug the programming cable into the radio's side jack. Connect the USB to your PC. Turn the radio ON.
Assigning specific VHF (134-174 MHz) or UHF (400-470/450-520 MHz) frequencies to each channel.
pigtail (DIN to 3.5mm jack) that connects the FIF-12 to the radio’s accessory port. Operating System : The software was originally designed for Windows 2000, XP, Vista, and 7 . To run it on Windows 10 or 11, you may need to use Compatibility Mode (set to Windows 7). Quality Two-Way Radios Step-by-Step Programming Setup Configure the COM Port : Open CE86, go to File > Configure , and select the COM port assigned to the FIF-12. Adjust Baud Rate : Set the baud rate to
The primary application used to program the VX-351 is the .
While waiting, he opened the tab of the software. Here lay the real power: TX Save (battery saver), Time-Out Timer (set to 60 seconds to stop chatterboxes from jamming the channel), BCL (Busy Channel Lockout), and Compander —a noise reduction feature that, when enabled, made audio sound like angels whispering through cotton.
He enabled Compander on all floor supervisor radios. It would reduce hiss and background slot machine noise. He disabled it on security radios—they needed raw, uncompressed audio to hear the nuance of a drunken argument.
. Users on Windows 10 or 11 may need to run the software in "Compatibility Mode" or use a Virtual Machine running an older OS. Programming Steps Driver Installation : Install the drivers for the cable before connecting it to your PC. Configuration Open the software and navigate to File > Configure Select the correct (it should show "FIF12" in parentheses). Baud Rate to 38,400 to ensure stable data transfer and prevent timeouts. Reading Data Ensure the radio is when you connect it. Select the "Read" or "Upload" option in the software. Turn the radio only when prompted by the software to begin the transfer. Editing & Writing
Here are some common programming tasks for the Vertex VX-351:
Once the software and cable are communicating, follow this specific sequence to avoid data corruption: Plug the programming cable into the radio's side jack. Connect the USB to your PC. Turn the radio ON.
